Featured Partners

Adart

FSU Logo

apvcoatings logo

Hunter logo

new logo

ZIPWALL®

Why Heat Dissipation in Building-Integrated Electronics Is a System Issue

Why Heat Dissipation in Building-Integrated Electronics Is a System Issue

In commercial buildings, electronics often operate out of sight: in luminaires, control units, and technical building systems. Their components generate heat that must travel from the point where it is produced to the surrounding environment. Along the way are printed circuit boards, housings, contact surfaces, and sometimes electrically insulating layers. If any part of this heat path is underestimated during design, even a material with high thermal conductivity can only help to a limited extent. For planning purposes, what matters is how the entire system performs under the intended installation conditions.

Where Heat in Commercial-Building Electronics Is Generated

An LED luminaire contains not only the light-emitting diodes themselves, but also electronic components for power supply and control. In building automation, compact controllers, sensors, and power supplies may be housed in enclosures or control cabinets. Power electronics, for example in the control of technical systems, must also dissipate the heat they generate. These are different applications, but the design question is similar: through which components and surfaces does the heat leave the electronics?

The answer depends on the specific installation scenario. A luminaire may dissipate heat through its carrier structure and housing; in a control unit, the arrangement of components, the enclosure, and the surrounding air all influence the heat path. A confined installation space is not automatically a thermal problem. It does, however, make it more important to identify the actual heat sources and the available paths for heat dissipation at an early stage, rather than thinking about cooling only after selecting individual materials.

The Heat Path Is More Than a Material Property

Heat does not flow directly from an electronic component into the room air. Depending on the design, it passes through the component body, a printed circuit board or another carrier, a thermal interface, and finally a cooling surface or housing. Each transition can limit the flow of heat. Especially between two solid surfaces, contact is not necessarily uniform across the full area: unevenness and tolerances can create gaps in which air remains trapped.

A thermal interface is intended to improve this contact. Whether it succeeds cannot be determined from the thermal conductivity of the material alone. Its thickness, the effective contact area, and the type of assembly also influence thermal resistance. Würth Elektronik therefore focuses on the system as a whole, consisting of the component, circuit carrier, assembly, housing, and environment. For building-integrated electronics, this means that a promising data-sheet value does not replace verification of the intended design.

Considering Thermal Coupling and Electrical Insulation Together

The interface between a heat-generating component and a cooling surface may need to fulfill two tasks: transfer heat and prevent an electrical connection. When evaluating solutions such as thermal interface solutions for electronics, the first question is therefore whether galvanic isolation is required at that specific point. A connection that appears thermally favorable is not automatically the right electrical solution.

The ZVEI guide “Strategies for Thermal Management” describes efficient heat transfer and electrical insulation as requirements that are often in tension with one another in many materials. Which property requires particular attention in a specific design depends, among other things, on the electrical function of the contact surfaces. Geometry is just as important: a very thin material may be unsuitable where there is a larger gap between two components, while a thicker layer can lengthen the heat path.

For design work, it is therefore helpful to separate the questions clearly. First, the electrical requirements at the interface are defined. It can then be assessed which material form can fill the existing gap under the intended assembly conditions while also fulfilling the thermal task. A general recommendation based solely on the material category would be too imprecise.

Selection Criteria for Thermal Interface Materials

Thermal interface materials are available in different forms because the surfaces to be connected also differ. Conformable gap fillers may be considered for gaps where component heights or manufacturing tolerances need to be compensated. Thermally conductive insulating films are used when a defined layer between contact surfaces is required and electrical insulation plays a role.

Ceramic insulating washers made of aluminum oxide or aluminum nitride are another material category for designs with corresponding thermal and electrical requirements. Belonging to such a category alone does not make a material suitable for a specific luminaire or control unit.

What matters is what happens at the actual interface. Are the surfaces parallel when they meet? Does the gap remain within the intended range even after fastening or closing the housing? Is there enough area available for heat transfer? With deformable materials, it is also important to consider how contact pressure and compression affect contact quality. A material may fill a gap, but with unfavorable assembly it may still fail to create uniform contact across the required area.

Supply format is also a design issue. Cutting and positioning must match the size of the contact area and the assembly sequence. In confined electronic assemblies, a misplaced or damaged layer can impair the function originally intended. Material comparison and assembly concept should therefore be considered together before a solution is defined for later production.

Technical Checkpoints for Building Planning

For building owners, project managers, and specialist planners, the issue is not to design every thermal material themselves. What matters is making the thermal function of electronic devices visible as part of technical planning. Especially in networked systems of building automation, different electronic components and controllers come together within the technical building infrastructure. Where is the heat source located? Through which components is heat intended to be dissipated, and where does it go afterward? Such questions concern, for example, the intended installation position, the available space around a housing, and coordination between the device manufacturer and the trades carrying out the work.

At the device-design level, the questions become more specific. In addition to heat generation, the actual gaps and contact surfaces must be identified. Electrical requirements at the interface must be clear before an insulating or non-insulating material is selected. It should also be clarified how the material is installed and whether contact pressure, fastening, and component tolerances in the finished device match the assumed heat path. These details are more meaningful than an isolated comparison of two thermal-conductivity values.

A calculated estimate can reveal unsuitable concepts at an early stage, but it reflects the eventual installation only as well as its assumptions. That is why technical review should also include the question of under which conditions a design is validated. A test on a free-standing prototype may describe a different environment than operation in a closed installation situation. Whether that difference matters can only be assessed on the basis of the specific device and its intended installation.

Especially in renovation projects, space constraints and existing installations may shape the integration of new electronics. If the installation situation is compared with the device design at an early stage, thermal assumptions can be examined more precisely. Planning does not need to prescribe a specific material family. It should ensure that the heat source, heat path, electrical requirements, and installation environment are considered together.

Heat dissipation in building-integrated electronics therefore does not begin with the search for the material with the highest performance figure. It begins with an understanding of the intended heat path. Contact geometry, layer thickness, electrical insulation, assembly, and environment jointly determine whether heat can leave the components as intended. Anyone who considers these relationships early in the design of luminaires, control units, and power-electronic devices creates a more robust basis for design engineering and subsequent validation.

Feature Image Source

Share this post :

Facebook
Twitter
LinkedIn
Pinterest

Stay close to the industry.

CCR updates, digital magazines, events, and partner insights.

Current Issue — CCR #10

Editorial & Third-Party Content Notice: Articles, press releases, company announcements, and accompanying media (including photography, graphics, and video) published on this site may be provided by third-party contributors, PR representatives, or wire sources as cited. Authorship and original copyrights remain with their respective holders.

Commercial Construction & Renovation is a registered service provider under the Digital Millennium Copyright Act (DMCA). To submit an inquiry, copyright claim, or formal takedown request, you may view our registered agent listing and official contact details via the U.S. Copyright Office DMCA Designated Agent Directory, or contact our compliance desk directly at publisher@ccr-mag.com.

Receive the CCR 2024 Idustry Report

Get ahead of your Competitors with CCR's FREE Industry Insider's Report 2024!

Always stay two steps ahead of your Competitors. Stay informed with the latest in the Industry. 

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

This site uses cookies to ensure that you get the best user experience. By choosing “Accept” you acknowledge this and that ccr-mag.com operates under the Fair Use Act. Furthermore, Changing privacy laws now require website visitors from EEA based countries to provide consent in order to use personalized advertising or data modeling with either Google Ads & Analytics. Find out more on the Privacy Policy & Terms of Use Page and our Editorial & DMCA Notice.