Featured Partners

FSU Logo

Adart

apvcoatings logo

ZIPWALL®

Hunter logo

Why Does My Safety Switch Keep Tripping?

You flick the safety switch back up, the lights come on, and ten minutes later the house goes dark again. It’s frustrating, but a safety switch that keeps tripping is doing exactly what it was built to do.

Something on that circuit is leaking electricity, and the switch cuts the power before the leak can hurt anyone. It’s one of the most common call-outs for any electrician Moreton Bay homeowners rely on, especially once the wet weather arrives, but you can often narrow it down yourself first.

Here’s how to work out where it’s coming from, and when to hand it to a licensed electrician.

What a Safety Switch Actually Does

A safety switch, also called a residual current device or RCD, constantly compares the electricity flowing out along the active wire with what comes back along the neutral. Those two should always match.

When they don’t, current is escaping somewhere it shouldn’t, usually to earth through a damaged cable, a wet fitting or, in the worst case, a person. Household safety switches trip at 30 milliamps, cutting the power fast enough to reduce the risk of a serious shock.

Safety switch or circuit breaker?

Check which device has tripped before you start. A safety switch has a small button marked T or Test, while a circuit breaker usually shows an amp rating such as 16A or 20A.

A breaker dropping out points to too much load on one circuit. A tripping safety switch means leakage, which is what this guide deals with.

Common Reasons a Safety Switch Keeps Tripping

A faulty appliance

This is the cause electricians find most often. As appliances age, worn elements, damaged cords and tired insulation let small amounts of current leak to earth.

Kettles, toasters, washing machines, dishwashers and fridges top the list, and an appliance can seem to work perfectly while still tripping your switch.

Water and moisture

If your safety switch trips when it rains, suspect moisture first. Outdoor power points, garden lights, pool equipment and fittings with perished seals all let water in, and water gives current an easy path to earth.

These faults tend to come and go. The switch trips during a storm, resets happily once things dry out, then trips again the next time it rains.

Damaged or ageing wiring

Cable insulation breaks down over the decades, and rats or possums chewing cables in the roof are a common culprit. So is a screw driven through a cable during a renovation.

If the switch trips with nothing plugged in at all, the fault is very likely in the fixed wiring or a fitting rather than an appliance.

Too many circuits on one safety switch

Every appliance leaks a tiny, harmless amount of current. Older switchboards often have one safety switch covering most of the house, and once those small leaks add up towards the 30mA limit, it trips with no single fault to blame.

A worn safety switch

Safety switches are mechanical and they wear out. An old one can start nuisance tripping, or worse, stop tripping when it should. An electrician can test the switch itself to confirm it’s still doing its job.

How to Find What’s Tripping Your Safety Switch

You can narrow it down with a simple process of elimination. Only do this with dry hands, standing somewhere dry, and never take the cover off the switchboard or touch any wiring.

  1. Unplug every appliance on the affected circuit. Pull the plugs out rather than switching off at the wall, and don’t forget the fridge or anything behind furniture.
  2. Reset the safety switch once.
  3. If it stays on, plug appliances back in one at a time, waiting about 30 seconds between each.
  4. If it trips straight after a particular appliance goes in, you’ve likely found the culprit. Leave it unplugged and get it repaired or replaced.
  5. For a lighting circuit, switch lights and fans on in groups to see which one sets it off.

Even if you don’t find the fault, knowing it only trips when the verandah light is on saves an electrician time.

If it trips with everything unplugged

Stop there. Leave the circuit off and call a licensed electrician, because the problem is in the wiring, a fixed fitting or the switch itself, and that’s all licensed work.

When to Call an Electrician Straight Away

Skip the troubleshooting and get a licensed electrician out if you notice:

  • A burning smell, scorch marks or melted plastic around power points or the switchboard
  • Buzzing, crackling or heat coming from the switchboard
  • A tingle or shock when touching an appliance, tap or fitting
  • Water near the switchboard or other electrical equipment
  • The switch tripping again the moment you reset it

Never force a safety switch to stay on or keep resetting it, since each reset puts power back into a faulty circuit. If someone has had a shock or there’s an electrical fire, call 000 first.

How to Stop It Happening Again

Press the test button on each safety switch every few months. It should trip straight away, and if it doesn’t, have it checked.

Replace cracked or weathered outdoor fittings before the wet season and keep an eye on appliance cords for damage. If your home still relies on one safety switch for most circuits, or still has old ceramic fuses, a switchboard upgrade with more safety switches will usually put an end to nuisance tripping.

Frequently Asked Questions

Why does my safety switch keep tripping with nothing plugged in?

When it trips with every appliance unplugged, the fault is almost always in the fixed wiring, a light or outdoor fitting, or the safety switch itself. A licensed electrician needs to track it down.

Why does my safety switch trip when it rains?

Water is getting into something electrical, usually an outdoor power point, garden light, pool equipment or a damaged cable. Repairing or properly sealing the affected fitting fixes it.

Is it safe to keep resetting a tripping safety switch?

No. One trip caused by a faulty kettle is nothing to worry about, but repeated tripping means there’s an active fault. Leave the circuit off and have it checked.

Share this post :

Facebook
Twitter
LinkedIn
Pinterest

Stay close to the industry.

CCR updates, digital magazines, events, and partner insights.

Current Issue — CCR #10

Editorial & Third-Party Content Notice: Articles, press releases, company announcements, and accompanying media (including photography, graphics, and video) published on this site may be provided by third-party contributors, PR representatives, or wire sources as cited. Authorship and original copyrights remain with their respective holders.

Commercial Construction & Renovation is a registered service provider under the Digital Millennium Copyright Act (DMCA). To submit an inquiry, copyright claim, or formal takedown request, you may view our registered agent listing and official contact details via the U.S. Copyright Office DMCA Designated Agent Directory, or contact our compliance desk directly at publisher@ccr-mag.com.

Receive the CCR 2024 Idustry Report

Get ahead of your Competitors with CCR's FREE Industry Insider's Report 2024!

Always stay two steps ahead of your Competitors. Stay informed with the latest in the Industry. 

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

This site uses cookies to ensure that you get the best user experience. By choosing “Accept” you acknowledge this and that ccr-mag.com operates under the Fair Use Act. Furthermore, Changing privacy laws now require website visitors from EEA based countries to provide consent in order to use personalized advertising or data modeling with either Google Ads & Analytics. Find out more on the Privacy Policy & Terms of Use Page and our Editorial & DMCA Notice.