Featured Partners

Adart

apvcoatings logo

FSU Logo

SignWav Elite

new logo

How To Keep Your HDD Locating System Working Day After Day

On any horizontal directional drilling project, the locator is only half of the story. The real work happens inside the drill head, where the transmitter sonde lives in some of the harshest conditions on the jobsite. Heat, vibration, fluid pressure and impact all act on that small electronic core. When it fails, your data disappears and the whole crew stops.

That is why DigiTrak transmitters remain such a focus for HDD contractors. The F series, especially F2 and F5, has earned a reputation for reliability, flexibility and strong performance in a wide range of soils and interference conditions. This article looks at how F2 and F5 sondes fit into a modern HDD fleet, how they differ in practice and how to choose and maintain the right mix for your rigs.

The role of the transmitter in an F series locating system

Every DigiTrak F series system is built around three components that work together:

  1. The transmitter sonde mounted in the drill head housing.
  2. The handheld receiver at the surface used by the locator hand.
  3. The in-cab remote display that feeds information to the driller.

The sonde generates an electromagnetic field at defined frequencies. The receiver reads this field and converts it into depth, pitch, roll and other data. The remote display mirrors that information for the operator.

If the transmitter is healthy, you get smooth, predictable readings and steering decisions are straightforward. If the transmitter starts to fail, everything downstream becomes unreliable. It is common to see jumping depth readings, intermittent signal loss or pitch values that do not match the way the rod string feels.

For that reason, many companies treat sondes as critical consumables rather than cheap accessories. Planning which sondes you use, how many spares you keep and how you maintain them is one of the simplest ways to stabilize your entire HDD operation.

Where the F2 sonde fits best

The F2 system is often the first F series locator many drillers learn on. It is straightforward, does not overwhelm crews with advanced settings and has enough power for most everyday utility work.

An F2 based setup is a good fit when:

  • Your typical bores are short or medium length service lines.
  • Depths are moderate and you rarely push the limits of the system.
  • Interference is present but manageable, for example in residential streets or light commercial areas.

Here, a dedicated digitrak f2 sonde gives you a balanced combination of range, ease of use and reliability. Crews quickly get used to its behavior and know how the signal responds when they move across the front and sides of the head.

Because F2 systems are so widely deployed, the sondes are common, housings are standardized and training material is easy to find. That makes F2 sondes a safe choice for companies building up their HDD capabilities or running multiple crews that need simple, dependable gear more than they need cutting edge features.

Why F5 sondes are used on more demanding projects

While F2 comfortably covers a large share of everyday work, your fleet may also face more complex situations. Deep bores, river or highway crossings, dense urban infrastructure and electrically noisy environments all push locating gear harder. This is where the F5 system usually comes in.

An F5 based rig is often used when you need:

  • Longer depth and data range for demanding pilot bores.
  • More frequency options to work around power lines, substations or rebar.
  • Higher resolution data for tight tolerances and complex steering paths.

For these applications, a dedicated digitrak f5 sonde paired with an F5 receiver and remote display lets you push further without sacrificing signal quality. The ability to choose and optimize frequency ranges in the field helps crews adapt to changing conditions instead of fighting constant interference.

On many jobsites, the F5 rig is seen as the flagship or problem solver unit. It handles the hardest bores on the schedule while other rigs, often built around F2 systems, take care of the more straightforward work.

Designing a mixed F2 and F5 sonde strategy

Very few companies use only one type of DigiTrak system. In practice, a mixed fleet is far more common and usually more economical. When you have both F2 and F5 locators in service, it makes sense to design a sonde strategy that treats them as parts of one overall toolkit.

A simple approach looks like this:

  • Assign an F5 rig with F5 sondes to projects where failure or inaccuracy would be extremely costly, such as river crossings, critical utilities or deep shots in heavy urban infrastructure.
  • Equip F2 rigs with F2 sondes for standard service lines, shorter shots and lower risk work.
  • Keep central stock of both sonde types at your yard, so transmitters can be rotated, serviced and tested between jobs.

This way you avoid overbuying high end hardware for situations where it is not needed, while still making sure that your toughest projects are supported by the best equipment you have.

How many sondes should each rig carry

No matter which system you rely on, the number of sondes on each rig is more than a budget question. It is a risk management issue. Relying on a single transmitter for an entire job is an invitation to downtime.

A practical baseline for each rig is:

  • One primary sonde in active use.
  • One backup sonde in the truck ready to swap in, ideally the same model so the crew does not need to adjust housing or expectations.

On top of that, your company should maintain additional transmitters in a central location. These can be fresh spares or units that have been recently tested, repaired or refurbished. If a rig reports a transmitter acting strangely, you can quickly replace it with a known good unit instead of forcing the crew to fight with a failing sonde.

New or refurbished sondes: finding the balance

Once you know how many transmitters you need, the next decision is how much of that pool should be brand new and how much can be refurbished.

New sondes from the manufacturer offer maximum lifespan and the latest design revisions. They are a logical choice for primary transmitters on rigs that handle high value projects.

Refurbished sondes, if sourced from a reliable specialist, can offer nearly the same performance at a lower cost. The key is that refurbishment must be more than just cleaning. You want transmitters that have been opened when needed, seals checked, electronics tested under load and depth and pitch validated against reference equipment.

Many contractors end up with a tiered model:

  • Brand new sondes as primaries on the most critical rigs.
  • Refurbished sondes as backups on those rigs and as primaries on less demanding F2 work.
  • Older transmitters rotated out or sent for evaluation if they show any sign of instability.

This approach keeps overall costs under control while still protecting your schedule and reputation.

Field practices that extend sonde life

Regardless of whether a sonde is new or refurbished, daily handling has a huge impact on how long it will last. Crews can significantly reduce failures with a few consistent habits:

  • Inspect o rings and threads every time you change batteries. Replace seals that look cut, flattened or dirty.
  • Keep battery contacts free of corrosion and moisture.
  • Never mix new and used batteries in the same transmitter.
  • Avoid overtightening caps, which can stress threads and seals.
  • Store sondes in padded cases when not in the head, not loose in tool bins.
  • Test suspect sondes at the yard under controlled conditions rather than forcing them through another full day of drilling.

These simple steps cost little in time but dramatically reduce emergency failures in the field, which is where downtime is most expensive.

Share this post :

Facebook
Twitter
LinkedIn
Pinterest

Stay close to the industry.

CCR updates, digital magazines, events, and partner insights.

Current Issue — CCR #10

Editorial & Third-Party Content Notice: Articles, press releases, company announcements, and accompanying media (including photography, graphics, and video) published on this site may be provided by third-party contributors, PR representatives, or wire sources as cited. Authorship and original copyrights remain with their respective holders.

Commercial Construction & Renovation is a registered service provider under the Digital Millennium Copyright Act (DMCA). To submit an inquiry, copyright claim, or formal takedown request, you may view our registered agent listing and official contact details via the U.S. Copyright Office DMCA Designated Agent Directory, or contact our compliance desk directly at publisher@ccr-mag.com.

Receive the CCR 2024 Idustry Report

Get ahead of your Competitors with CCR's FREE Industry Insider's Report 2024!

Always stay two steps ahead of your Competitors. Stay informed with the latest in the Industry. 

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

This site uses cookies to ensure that you get the best user experience. By choosing “Accept” you acknowledge this and that ccr-mag.com operates under the Fair Use Act. Furthermore, Changing privacy laws now require website visitors from EEA based countries to provide consent in order to use personalized advertising or data modeling with either Google Ads & Analytics. Find out more on the Privacy Policy & Terms of Use Page and our Editorial & DMCA Notice.