A CAV DPA injection pump number helps identify the pump’s application, calibration, and service configuration. Reading it correctly makes it easier to find compatible replacement parts, select a rebuild kit, or confirm whether a used pump matches your diesel engine.
The same pump body may appear on several tractors or industrial engines. However, the internal settings can be different. A pump that looks correct may still deliver the wrong amount of fuel or use the wrong injection timing.
What Is a CAV DPA Injection Pump?
The CAV DPA is a rotary mechanical diesel fuel injection pump. Lucas CAV produced many versions for agricultural, construction, and industrial engines. Later products and replacement listings may appear under the Delphi name.
The pump performs several jobs:
- Draws fuel from the supply system
- Meters the correct amount for each cylinder
- Sends fuel to the injectors
- Controls injection timing
- Adjusts delivery as engine speed and load change
A typical CAV fuel injection pump contains a drive shaft, distributor rotor, pumping elements, governor, transfer pump, and timing mechanism. Wear or contamination in any of these areas can cause hard starting, uneven running, smoke, or low power.
Where Can You Find the Part Number?
The main identification number is usually stamped on a small metal plate fixed to the pump. Depending on the engine, the plate may sit near the governor housing, mounting flange, or side cover.
Clean the plate carefully before reading it. Oil, dust, and old paint can hide individual characters. Take a photograph from several angles, then compare the number with the engine and machine records.
Do not confuse these numbers:
- Pump specification number
- Pump serial number
- Engine serial number
- Machine model number
- Casting number
They identify different items. A casting number may describe only the pump housing and may not confirm the internal calibration.
How Do You Read a CAV DPA Number?
Identify the Pump Family
Look for markings such as:
- CAV DPA
- Lucas CAV
- Delphi
- Delphi fuel injection pump
These markings identify the general pump family. A later Delphi listing may be a replacement for an older Lucas CAV unit, but the complete specification still needs to match.
Check the Specification Code
The longer number on the plate is usually the most important detail. It connects the pump to a particular engine application and calibration.
Numbering systems can vary, so do not assume that every digit has one universal meaning. Some sections may indicate pump type, while other information identifies delivery settings, governor characteristics, or application details. A reputable rebuilder should verify the complete number rather than relying on one digit.
Confirm Rotation and Drive Arrangement
Pump rotation must match the engine. A pump designed to turn in the opposite direction may fail to operate correctly or deliver fuel at the wrong time.
Also compare:
- Drive gear or hub design
- Mounting flange
- Bolt spacing
- Fuel inlet and return ports
- Delivery outlet positions
- Stop and throttle lever locations
- Timing adjustment range
These details can differ even when two pumps share the same DPA housing.
Which Parts Are Commonly Replaced?
A pump does not always need complete replacement. A qualified technician may inspect and replace worn components such as:
- Shaft seals
- O-rings
- Bearings
- Governor springs
- Metering valve parts
- Transfer pump components
- Delivery valve seals
- Shims and gaskets
A CAV injection pump rebuild kit commonly contains seals, gaskets, and other service items. Contents vary by pump number, so confirm the kit application before ordering.
A basic seal replacement may not solve a pump with a worn cam ring, damaged rotor, corrosion, or severe contamination. After rebuilding, the pump should normally be tested and calibrated on a suitable test bench.
How Do You Verify Compatibility?
Use the pump plate, engine information, and machine records together. Before choosing an Injection Pump, replacement assembly, or internal component, confirm:
- The complete pump specification number
- Engine make and model
- Machine model and serial range
- Number of cylinders
- Rotation direction
- Mounting and drive arrangement
- Injector line and outlet configuration
- Fuel inlet and return connection sizes
A Perkins fuel injection pump diagram can help identify the delivery lines and fittings. It cannot, by itself, prove that a pump calibration is correct.
The same caution applies to a John Deere injector pump rebuild kit. A kit may fit one engine version but not another with a similar model name. Always compare the exact pump code.
What If the Identification Plate Is Unreadable?
Start by photographing the entire pump. Record the engine plate, number of cylinders, machine model, and any visible casting marks. Note the position of the fuel outlets, throttle lever, and stop mechanism.
A specialist may identify the pump from these details. However, avoid guessing when ordering internal parts. The wrong governor spring, rotor, or delivery setting can lead to hard starting, excessive smoke, poor performance, or overspeed.
Final Thoughts
The CAV DPA part number is more than a general model label. It helps identify a specific pump application, calibration, rotation, and mounting design. Read the complete plate, compare it with the engine information, and verify technical details before buying injection pump parts or a rebuild kit.
Careful identification takes a few extra minutes. It can prevent an incorrect order and save much more time during installation and testing.






